Click on a panel component below to view the description for that component.

FAULT POWER SUPPLY SPC/IPC
indicator

This indicator light turns on when a disturbance occurs in the power supply in-line to the control cabinet or within control cabinet. When the light turns On: Control panel power supply = 00-F04 dropped out. Automatic circuit-breaker for control voltage =00-F06 dropped out. No load voltage. =00-F60 dropped out. IPC (monitor screen) power supply =00-F08 dropped out (the main motor may still be running in these cases). When the light is extinguished: Motor protective switch =00-Q20 dropped out. Device =00-G02 in fault. Automatic circuit-breaker =00-F40 dropped out.

Click here to close popup

AXIS + pushbutton

Push the AXIS+ button to move the wedge forward. This will increase the coining force. The AXIS+ button can be pushed whether the clutch is engaged or disengaged.

Click here to close popup

MACHINE ON pushbutton

Push the MACHINE ON button to turn on the Main Motor and the lubrication system (if the press uses a lubrication system). After the button is pushed, the button will illuminate green.

Click here to close popup

FAULT RESET pushbutton

Push this button to reset faults.

Click here to close popup

DOORS LOCK pushbutton

Push this button to lock the front sliding door (1) and the 2 back doors (2 & 3). The doors must be closed before they can be locked.

Click here to close popup

FEED PLATE NOT IN END POSITION indicator light

This indicator light turns on when one of the two proximity switches that monitor the Feed Plate Gearbox Working position and Service position do not detect the Feed Plate Gearbox.

Click here to close popup

CLUTCH ON pushbutton

Push this button to engage the clutch.

Click here to close popup

PRESELECTED MOTION START
pushbutton

This button is used as a two-hand safety device for operating press components in manual mode. In order to move a component with the machine doors open, you must push this button while turning the APPROVAL switch to the right at the same time.

Click here to close popup

AXIS - pushbutton

Push the AXIS- button to move the wedge backward. This will decrease the coining force. The AXIS- button can be pushed whether the clutch is engaged or disengaged.

Click here to close popup

MACHINE OFF pushbutton

Pushing this button causes the flywheel to be braked down and then stopped. If the MACHINE OFF button is activated while the clutch is engaged, the slide stops at rear dead center, and, thereafter, the flywheel is braked down.

Click here to close popup

INPUT DATA keyswitch

The Input Data keyswitch must be turned to the right before certain data can be input into the system.

Click here to close popup

DOORS UNLOCK pushbutton

Push this button to unlock the front sliding door (1) and the 2 back doors (2 & 3). The doors must be unlocked before they can be opened

Click here to close popup

CLUTCH OFF pushbutton

Push this button to disengage the clutch.

Click here to close popup

WINDOW FRONT OPEN pushbutton

Push this button to open the small front (sash) door on the press. This pushbutton is operational only when the press is in Hand Feed Mode.

Click here to close popup

WINDOW FRONT CLOSE pushbutton

Push this button to close the small front (sash) door on the press. This pushbutton is operational only when the press is in Hand Feed Mode. You must hold the button in until the door is closed.

Click here to close popup

PUNCH CLEANING pushbutton

Pushing this button activates an auxiliary ejector that pushes the Obverse Die outside the collar so the face can be wiped off. This pushbutton is operational in both Hand Feed and Automatic Feed Mode.

Click here to close popup

Component 17

Click here to close popup

Component 18

This is component 18.

Click here to close popup

Component 19

This is component 19.

Click here to close popup

Component 20

This is component 20.

Click here to close popup

Component 21

This is component 21.

Click here to close popup

Component 22

This is component 22.

Click here to close popup

Component 23

This is component 23.

Click here to close popup

Component 24

This is component 24.

Click here to close popup